PDA

View Full Version : Engine

Pages : 1 2 [3]
  1. engine shop questions
  2. Help, Strange misfiring
  3. Replacing Headgasket
  4. Weird cylinder loss issue.
  5. Crank Case Vent Solution
  6. Mighty Max 4g64 connecting rods.
  7. messed up head.
  8. Water pump was the initial problem, engine is going snafu
  9. Boost Drop Off
  10. Wandering Fuel Pressure
  11. Eagle rod key orientation
  12. Torque Plate
  13. dip stick
  14. PLEASE HELP! Need pro dsmer to come give me help! willing to pay.
  15. Would a smaller WG help my boost taper?
  16. evo III downpipe??
  17. evo parts that fit the dsm
  18. Local Dsm help please
  19. Where to go
  20. rebuild help
  21. Engine Cooling
  22. Bumper cover
  23. engine rebuild
  24. Planning on undertaking my FMIC behemoth piping, not a clue where to start.
  25. Turbo ID, help!
  26. 359/2000's new heart
  27. Head gasket blew again under warranty, re-machining hazards?
  28. Possible Cause of Phantom Knock
  29. Rod knock?
  30. Oil pan short bolts on a 2g
  31. Engine cooling
  32. Fuel cut?
  33. Unconventional Conventional Wisdom?
  34. Radiator Core Repair
  35. Battery, coolant, and brake light come on after I start the car?
  36. Indiana help
  37. I need help please!!!!
  38. Tech Discussion: Holding Boost in 3rd
  39. Engine gaskets/seals
  40. Afr problems, any idea?
  41. whats happening?
  42. Car running terrible when cold....
  43. Anyone run Manifold spacers?
  44. In dire need of a reducing coupler!
  45. Fuel in Radiator Coolant High Pressure
  46. Revised lifters need evo rockers?
  47. Custom fabrication
  48. Running like crap. Mega Lean
  49. Fuel pump issue, I am completely stumped.
  50. Cyl. 1 Misfire- P. Transistor Testing Question?
  51. sound of idle is'nt right.
  52. Running Issue When car is cold
  53. What headgasket?
  54. Why eliminate balance shaft
  55. Mitsubishi downloads
  56. Car wont boost over 10 psi?
  57. Clanking sound from engine
  58. Blown Turbo, Anything else?
  59. Turbo re-build
  60. po446 still
  61. 6 bolt vs 7 bolt crank pulley
  62. Engine priming Question
  63. Power Cuts Out?
  64. Changing a Lifter
  65. coolant hard line that goes from t stat housing to oil filter housing
  66. Need a little help
  67. Is anyone available to give me some pointers on 2ghead/1g block?
  68. Piston Slap
  69. diameters of rods to tap for specific nut sizes?
  70. Gasket PN
  71. dsm noob in need of help
  72. Billet Aluminum 4G63 Block
  73. Comments on this head resurface job?
  74. 2g maf
  75. 4g64 crank or stock.. 6 bolt
  76. Misfire Issues
  77. Rod Pin Width
  78. O2 Sensor Issues
  79. Intercooler pipe
  80. no start, cant think of anything else
  81. Custom air conditioning lines
  82. Brake problem
  83. A1 6 bolt Head Stud info.
  84. Talon died, no power- any ideas?
  85. Motor just spins.
  86. All i did was move injectors???
  87. Who should I take it to?
  88. Would +1mm Valves Only On the Exhaust Side Increase Power?
  89. Running rough
  90. mysterious rattle from under the hood
  91. Evo8 exhaust mani?
  92. solid lifters...
  93. CAM timing - does this look right?
  94. compression test results. good or bad?
  95. looking for a good machine shop
  96. my 1998 gsx auto wont go past 20 mph
  97. want to do 6 bolt swap in my 99 gst
  98. MLS Vs. Stock head gasket?
  99. TB replacement & BS removal help
  100. Timing belt assistance in Colorado springs?
  101. 2g cam and crank sensor in a 1g?