ErikW
February 22nd, 2007, 09:23 PM
I'M SORRY TO SAY... MY WRENCHING DAYS ARE OVER GUYS!
I have a few things that I wanted to save until the next rebuild. My new (renting) neighbor is bullying his things into my side of the garage space. I now have very minimal room. The HOA is less than empathetic even though I have the lesser half of space available than anyone else. And I'm an owner.
:(
I have been out of the loop for a while and I don't know what the value on these parts can go for. So I have to try to get something back outta them since most of these items are very slightly used and I'm in financial difficulties right now.
I have a brand new 6bolt, 1g, oil cooler that was purchased at MHM and was used on the car for a month before I replaced it with a '90 Air Oil Cooler setup. This item was for 350.oo. 195.oo? I will sell at reasonable best offer.
Item 2 is for a 6bolt Stock awd flywheel stepped and balanced. Comes complete with ring gear and pins. cost me 250.oo again Id like to get as much as anyone would back out of this expense but... Send me your offers. 145.oo?
Practically new 6bolt trans. I had it in the car for about 3~4k miles before I purchased a used TRE one. I still might use this one as a good platform for rebuilding a serious racing tranny. But I do not know how I'll ever find the money for that right now. I could use the money for more important things now (unfortunately).. Purchased it from Emich Jeep/Eagle for 1800.oo.
1000.oo?
my tried and true 6bolt engine block. I'm willing to let this go for 50.oo. I have a crank for it too.
I have a head that could be a good racing head. It has a 3angle valve job for 1mm over valves. Intake and exhaust runners deburred and slightly ported.This head's deck may need cleaning up. Needs new valves and valve guides. with 3g lifters. 120.oo
Silver powder coated crank case cover. all bolt holes intact. 75$ firm.
Misc. 2.5" galvanized piping straight.
SS 3" U bend. F.S.
misc short ones for jointery
3" ss straight 18~20ins
2g fuel pump.
190 ND pump.
lost your BISS? I have a spare.
thank you
erik
I have a few things that I wanted to save until the next rebuild. My new (renting) neighbor is bullying his things into my side of the garage space. I now have very minimal room. The HOA is less than empathetic even though I have the lesser half of space available than anyone else. And I'm an owner.
:(
I have been out of the loop for a while and I don't know what the value on these parts can go for. So I have to try to get something back outta them since most of these items are very slightly used and I'm in financial difficulties right now.
I have a brand new 6bolt, 1g, oil cooler that was purchased at MHM and was used on the car for a month before I replaced it with a '90 Air Oil Cooler setup. This item was for 350.oo. 195.oo? I will sell at reasonable best offer.
Item 2 is for a 6bolt Stock awd flywheel stepped and balanced. Comes complete with ring gear and pins. cost me 250.oo again Id like to get as much as anyone would back out of this expense but... Send me your offers. 145.oo?
Practically new 6bolt trans. I had it in the car for about 3~4k miles before I purchased a used TRE one. I still might use this one as a good platform for rebuilding a serious racing tranny. But I do not know how I'll ever find the money for that right now. I could use the money for more important things now (unfortunately).. Purchased it from Emich Jeep/Eagle for 1800.oo.
1000.oo?
my tried and true 6bolt engine block. I'm willing to let this go for 50.oo. I have a crank for it too.
I have a head that could be a good racing head. It has a 3angle valve job for 1mm over valves. Intake and exhaust runners deburred and slightly ported.This head's deck may need cleaning up. Needs new valves and valve guides. with 3g lifters. 120.oo
Silver powder coated crank case cover. all bolt holes intact. 75$ firm.
Misc. 2.5" galvanized piping straight.
SS 3" U bend. F.S.
misc short ones for jointery
3" ss straight 18~20ins
2g fuel pump.
190 ND pump.
lost your BISS? I have a spare.
thank you
erik